As the name suggests, an error code is a reference that the machine will display if there is an error. Now, not all error codes mean something is faulty with the machine. For example, a Robopac E60 error code means “Film Breakage”. The film may of course have torn, but it could also have run out. The simple solution is to check the film, and replace with a new one if the film has run out.
The following tables offer a detailed breakdown of the possible error codes you may see when using a Robopac Pallet Wrapping Machine
Here at KB Packaging, we offer both the 508 and 708 Robopac Roboplat Pallet Wrappers, and both of the models share the same error codes. The below table details the error code, the problem, the cause, and the solution.
| Error Code | Problem | Cause | Solution |
|---|---|---|---|
| E01 | Emergency mushroom-head button alarm | Emergency mushroom-head button pressed | Emergency mushroom-head button pressed |
| E02 | Carriage emergency | An obstacle has been detected along the trajectory during the spool carriage downstroke | Remove the obstacle and press the “Reset” button |
| E03 | Hand pallet truck emergency | An obstacle has been detected on the pallet loading/unloading ramp | Remove the obstacle and press the “Reset” button |
| E04 | Protection alarm | Intervention of safety barriers or open door | Remove the obstacle and press the “Reset” button |
| E30 | Inverter alarm: 1. Table 2. Carriage 3. Stretch 4. Pre-stretch 5. Presser | POWER DRIVER LOW POWER DRIVER HIGH OVER VOLTAGE MAX VOLTAGE UNDER VOLTAGE HW POWER CURRENT OVER HEAT PHASE FAIL CURRENT MAX CURRENT INT MAX PARAMETER WRONG COM.ERROR | Contact technical support |
| E60 | “Film breakage” alarm | The film has broken or spool is finished | Insert the film or replace spool |
| E61 | Table synchronisation alarm | A fault or an obstacle is preventing the table from moving | Solve the fault or remove the obstacle and press the “Reset” button |
| E64 | Blocked carriage alarm | The carriage has stopped its travel | Remove the obstacle and press the “Reset” button |
| E65 | Blocked presser alarm | The presser has stopped its travel. | Remove the obstacle and press the “Reset” button |
| E71 | Presser position alarm | Incorrect presser position | Move the presser down and start the cycle |
| E83 | MODBUS alarm | Electronic fault | Contact technical support |
The below table details the error code, the problem, the cause, and the solution for the Robopac Masterplat Pallet Wrappers.
| Error Code | Problem | Cause | Solution |
| E01 | Emergency mushroom-head button alarm | Emergency mushroom-head button pressed | Reset the button and press the “Reset” button |
| E02 | Carriage emergency | An obstacle has been detected along the trajectory during the spool carriage downstroke | Remove the obstacle and press the “Reset” button |
| E03 | Hand pallet truck emergency | An obstacle has been detected on the pallet loading/unloading ramp | Remove the obstacle and press the “Reset” button |
| E04 | Protection alarm | Intervention of safety barriers or open door | Remove the obstacle and press the “Reset” button |
| E30 | Inverter alarm: 1. Table 2. Carriage 3. Stretch | Motor faults | Contact technical support |
| E60 | “Film breakage” alarm | The film has broken or spool is finished | Insert the film or replace spool |
| E61 | Blocked table alarm | A fault or an obstacle is preventing the table from moving | Solve the fault or remove the obstacle and press the “Reset” button |
| E83 | Error alarm Communication | Electronic fault | Contact technical support |
The below table details the error code, the problem, the cause, and the solution for the Robopac Masterplat Pallet Wrappers.
| No. of Flashes | Problem | Cause | Solution |
|---|---|---|---|
| 1 Flash | Inverter communication alarm | Electronic fault | Contact technical support |
| 2 Flashes | Plate alarm | Emergency plate pressed | Release the emergency plate and reset the machine |
| 3 Flashes | Motor alarm | Inverter overload | Remove the overload cause. Switch the machine off and then on again |
| 4 Flashes | Table alarm | A fault or an obstacle is preventing the table from moving | Remove the fault cause. Switch the machine off and then on again |
| 5 Flashes | Film breakage alarm | Film breakage detected during a wrapping cycle | Re-join the film to the product and reset the machine (Only available with R-Connect with film monitoring device) |
| 6 Flashes | Carriage alarm | A fault or an obstacle is preventing the film carriage from moving | Remove the fault cause. Switch the machine off and then on again |
| 7 Flashes | Pallet start alarm | If the pallet is not present on the machine, the machine will remain stationary when the CYCLE START button is pressed | Position the product on the table and start a new cycle |
If you’d like further information on the products and service we offer at KB Packaging, get in touch today! You can reach us by calling 0115 944 1600 or by emailing info@kbpackaging.com.
